Catalog

Carving Block Maker Model CB300X2

  • carving block maker To create special effects, freeze flowers, wedding vows, or just about anything imaginable into the block of ice.
  • Create a colored block of ice by using a food coloring mixture.
  • A stainless steel lifter plate is frozen approximately ½ " into each end of the block to help lift the finished block from the chamber.
  • A pump circulates the water to keep impurities from freezing into the block of ice. Excess water and impurities are removed from the top of the block prior to harvesting by use of a common wet and dry vacuum. Proper placement of the pump is critical to the clarity of the ice. Each day of the freezing cycle the position of the pump must be changed for continued ice clarity.
  • Produces a crystal clear block of ice for sculptures. A pleasure for the carver to work with and a delightful product for your customer.
  • Blocks of ice are frozen in a plastic liner and then placed inside a cardboard box for storage and handling.
  • Each unit will produce two blocks every three days. The recommended ambient temperature for maximum productivity is 72 degrees F. (Cold temperatures can cause cracking in the blocks and much warmer temperatures may slow the freezing cycle.)
  • One block of ice can be removed and the machine refilled within 15 minutes or less, by one person. Creates an off-season income.

crystal clear
            blockSpecifications

  • Outside dimensions: 48 ½ " X 51 ¼ " X 42"H
  • Requires one ½ HP – 115V, 50/60 HZ – single phase condensing unit for self- contained or remote capabilities
  • Cabinet is all galvanized construction
  • Circulating pump: 115V-60 HZ

structural steel shapesCarving Block Hoist Model HST

  • Designed specifically for use with CB300 block maker series and tilt cart.
  • This design is compact, easy to maneuver and very reliable.
  • The gear reduction chain hoist offers ease and reliability with minimal pull.
  • The lifter bar hooks onto the lifter plates that were frozen into each end of the block of ice. After gently flexing the sides of each chamber, slowly hoist the block of ice out of the machine.
  • The carving block hoist is designed to be used with the tilt cart.
  • Place approximately 50lbs. of weight on the hoist base for additional stability when lifting out the block.

Specifications

  • Outside dimensions: 84 ¾ " high, 25" wide, 47" deep
  • Weight: 150 lbs.
  • Load limit: 400 lbs.
  • Constructed of: structural steel

Carving Block Tilt Cart Model Tilt

  • carving block tiltDesigned to be used with the block hoist.
  • Roll the tilt cart between the hoist legs and slowly lower the block of ice down onto the cart.
  • The block of ice is ready to be moved to your work area.
  • To box the block of ice once it's on the tilt cart, lift approximately 40 lbs. from one end. While the tilt cart and block of ice are on one end, slide the box over the ice, lower the block and the tilt cart and then lift the other end of the tilt cart to close the box.

Specifications

  • Outside dimensions: 41" long, 18" wide, 24" tall
  • Weight: 50 lbs.
  • Load limit: One block of ice
  • Constructed of: structural steel

power shaver modelPower Shaver Model PWRSHVR

  • Breezes through block for a clean-shaven look with little to no impressions left on the block from the shaver.
  • Speeds up production for larger production facilities.
  • Takes less than 1 minute to shave a block with little to no effort.
  • Designed for the uniform packaging of the block for shipping purposes.

Specifications

  • 44 ½ "H X 34" W X 37"L
  • 1 ½ HP – 220V 60HZ
  • 1725 RPM
  • Constructed of: steel body, nylon wheels

manual shaver modelCLINEBELL'S Manual Shaver Model MNSHVR

  • Inexpensive way to uniformly shave the carving block for shipping purposes. Ideal for smaller operations.

Specifications

  • 38"H X 34" W X 37" L
  • Steel construction
  • Heavy duty steel blade, easily sharpened

11-Pound Block Maker Model B56

  • pound block makerLets you freeze blocks in Polyethylene bags. No Glycol solution. No circulating pump. No ice cans needed.
  • No messy harvest tanks. No defrosting. Blocks are hard frozen when taken to the freezer.
  • Bags of water are placed between refrigerated plates for freezing.
  • 56 bags can be filled with water and loaded into cabinet in 20 minutes or less.
  • 56 11 lb. blocks of ice are produced each day using 1 ½ HP condensing unit. Two 1 ½ HP condensing units or one 3 HP condensing unit will net 56 blocks twice per day.
  • This process provides a more cost effective and sanitary end product.
  • The cabinet is designed for remote installation.
  • A bag fill device is available as an accessory.

polyethylene bags productionSpecifications

  • Outside dimensions: 40 ½ " X 80 ½ " X 37" high.
  • Requires one 1 ½ HP condensing unit, 230 volts, single phase, 50/60 HZ to pull blocks once per day or two 1 ½ HP condensing units or 3HP condensing unit to pull blocks twice per day.
  • Weight: 750 lbs.
  • Block size: 4 1/8 " X 8 ¾ " X 10" high.

Snow Cone Block Maker Model S60

  • remote installation serviceLet's you freeze hard frozen blocks of ice in Polyethylene bags. No circulating pump. No ice cans needed.
  • No messy harvesting tank. No defrosting. Blocks are hard frozen when taken to the freezer.
  • Bags of water are placed between refrigerated plates for freezing. 60 bags of ice can be filled with water and loaded into the cabinet in 25 minutes or less by one person.
  • 60 ten pound blocks of ice are produced each day using one 1 ½ HP condensing unit.
  • This process provides a more cost effective and sanitary end product.
  • The 5 ½ " square block of ice is not likely to "blow up" in the ice shaver, unlike compacted ice.
  • The compact size allows placement in almost any location.
  • The cabinet is designed for remote installation.
  • The bag fill device is available as an accessory.

snow cone blockSpecifications

  • Outside dimensions of cabinet: 40 ½ "D X 80 ½ " W X 37" H
  • Requires one 1 ½ HP condensing unit, 230V, single phase, 50/60HZ.
  • Weight: 750 lbs.
  • Final block size: 5 ½ " X 5 ½ " X 10"

Bag Fill Device

  • bag fill deviceThe double sided Bag Fill Device allows bags to be filled more accurately and efficiently.
  • Bag lip is pierced over two pins at the top of each station allowing the remainder of the bag to rest in the bottom trough.
  • Using a counter-balance weight system, each trough will tilt forward when the bag is filled correctly. Just shut the water off and tie the bag closed. Be sure to leave enough air in the bag to allow for expansion as the block freezes.
  • With experience, you can have one bag filling while you close the other bag and place it in the machine.
  • The Bag Fill Device can be placed on a stationary table or on a cart for mobility and efficiency.
  • The Bag Fill Device can be hooked up to a copper water line or by using a "food grade" hose.

Specifications

  • Outside dimensions: 24" X 24" X 24'
  • Weight: 37 lbs.
  • Constructed of galvanized steel

 

Bag Supplies and Boxes for Carving Block:

CB300L (Carving Block Liners)  50 in a box.                           20" X 40" X 15"

CB300B (Carving Block Boxes) 10 per bundle                         20" X 40" X 10"

Bag Supplies for B56 and S60 Block Makers:

Bag #18 (B56 Block Maker, 11 lb block) 500 per roll              11 1/2" X 21 1/2" X .0021

Bag #19 (B56 Block Maker,  8 lb snow cone) 500 per roll        8 3/4" X 21 1/2" X .0021

Bag #28 (S60 Block Maker, 10 lb snow cone) 500 per roll      10 1/2" X 20 1/2" X .0021

 

Print Version Print Version       Send to a friend Send to a friend